Terrestrial | Airborne | Mobile | Short Range | Business | Equipment | Hardware | Software | BIM | Heritage | Forensics | Events & Education  



remove subscribe

LiDAR Magazine Today


follow us on Twitter 

Sponsored By

TAS Lidar Content
TAS Content
Meet the Authors
Check out our fine lineup of writers. Each an expert in his or her field.
Sponsored By

Partner Sites

American Surveyor







Spatial Media LLC properties




LinkedIn Group
facebook group

Home arrow News arrow American Surveyor Lidar Content arrow Jerusalem's Temple Mount: Historic Preservation with 3D Laser Scanning   LiDARmag     

Jerusalem's Temple Mount: Historic Preservation with 3D Laser Scanning Print E-mail
Written by Bruce Jenkins   
Wednesday, 28 February 2007

A 1.851Mb PDF of this article, complete with images, is available by clicking HERE 

The Temple Mount is a 35-acre historic site in the Old City of Jerusalem which is of central importance to Judaism, Islam and Christianity. It was the site of the first and second Jewish Temples in Jerusalem and is currently the site of two major Muslim shrines, the Dome of the Rock and Al-Aqsa Mosque. The mount is hemmed in by an enclosure wall that was erected to create a level platform on which Herod the Great could rebuild the Jewish Temple in the first century B.C. In February 2004 an earthquake displaced a portion of the mount's eastern wall ( cover photo and Figure 1). To analyze the deformation and determine whether remediation was needed, the Israel Antiquities Authority engaged Mabat 3D Technologies, Ltd., of Tirat-Carmel, Israel to document and measure the displacement using 3D laser scanning.

Displacement Analysis Workflow
Mabat CEO Arik Degani describes how his firm scanned the wall after the earthquake, then compared the resulting data with reference scans taken more than three years earlier. To begin, the survey team placed 15 targets on rocks lying in front of the wall and located these precisely with total station surveying. "We do this to eliminate as much error as possible," Degani explains. "You need targets to determine whether you have 5mm of displacement in the wall or 10mm. In displacement analysis, every 2mm counts." Then the team scanned the eastern wall using its Leica HDS2500 (Mabat has since upgraded to an HDS3000). Total field time was between five and six hours.

Post-processing and extraction of measurements were done in Cyclone. Deliverables were a TIN mesh showing the wall's geometry after the earthquake compared with before (Figures 2 and 3), and sections through the TIN mesh used to generate displacement maps (Figure 4). The TIN mesh and displacement maps were exported to AutoCAD at the client's request. For every hour of field time, 1.5 to 2 hours of office work were required, Degani reports.

Using this data, the Antiquities Authority determined that earthquake-induced displacement was not severe enough to threaten the wall's stability, Mabat reports, so immediate remediation was not needed.

Bulge in Southern Wall
Baseline data documenting the eastern wall's pre-earthquake position had been collected by Mabat in an earlier project. As part of an engagement to monitor the walls, in October 2000 the firm was called in to document a bulge in a different location -- in this case the mount's southern wall (Figure 5). This bulge probably resulted from lateral loads exacerbated by construction and excavation activity on the mount, according to Mabat. "At the same time as scanning this bulge," Degani notes, "we were asked to monitor the southern part of the eastern wall, from the south corner to about one hundred meters away." Thus the firm had reference data on the eastern wall when the earthquake hit.

Field time to scan the southern wall was likewise five to six hours, including total station-based location of targets. In post-processing, Cyclone was used to cut sections through the point cloud every 25cm and generate contour lines (Figure 6). Displacements of 9-15mm were identified. This was judged significant, and repairs were undertaken as a result.

Bruce Jenkins is managing partner, senior analyst, and cofounder of Spar Point Research in Danvers, Massachusetts. Spar Point Research is a technology business research firm focused on terrestrial 3D laser scanning and related dimensional control technologies.

A 1.851Mb PDF of this article, complete with images, is available by clicking HERE

< Prev   Next >


Share this page with your favorite social networks! 


LiDARmag Exclusive Online-only Article ticker
Featured LiDAR MAG Events
List Your Event Here
contact LiDAR


Klau Introduces

press [at] lidarmag.com
Online Internet Content


White Papers

post a job
Reach our audience of Professional land surveyors and Geo-Technology professionals with your career ad. Feel free to contact us if you need additional information.

News Feeds

Subscribe to LiDAR MAG updates via friendfeed

Need Help? See this RSS Tutorial

©Spatial Media LLC - All rights reserved / Privacy Statement
Spatial Media LLC
7820B Wormans Mill Road, #236
Frederick MD 21701
301-695-1538 - fax